How to Make a Sword
- a Beginners 10 Step Guide

What follows is guide on how to make a sword using the most simple and straightforward method suitable for a beginner - stock removal (in other words, taking a length of steel and shaping it into a fully functional sword).

While this guide has been designed with the beginner in mind, learning how to make a sword is a fairly steep learning curve, requiring a fair amount of experience working with power tools - so we do not recommend this method if you are under 18 years old or are not a natural DIYer..

That said, for those of you willing to give it a try, the following guide is a great place to learn the basics of how to make your a sword based on the techniques used by sword artisan Brendan Olszowy (aka 'Brenno') from Fable Blades.com

Step by Step Guide on How to Make a Sword

This free illustrated guide is both straightfoward and presented in a step by step format, so with a little skill and elbow grease, it's possible to create a seriously functional, original sword that you can be proud to call your own.


HOW TO MAKE A SWORD: A STEP BY STEP GUIDE

Our basic guide on how to make a sword using the 'stock removal' method.

STEP ONE: Outline Your Design

Decide what type of design you want for your new knife, dagger, or sword. Mark your steel where the outline of the blade will be, from tip all the way to the end of the tang.

Step by Step Guide on How to Make a Sword

After marking the outline on your steel, then drill out any places that you won't be able to get to with an angle grinder. (Make sure to drill first - after grinding, the steel hardens and it will be almost impossible to drill.)

Step by Step Guide on How to Make a Sword

This step is unnecessary for simple straight blades.


STEP TWO: Cut out the outline

Using a 5" angle grinder (with 1mm cutoff wheels), cut along your outline, leaving some room for error (about 2mm away from the line is good, once you get more practice you can try going closer).

Step by Step Guide on How to Make a Sword


STEP THREE: Refine the profile

Refine the profile to the exact lines that you want, taking off that 2mm that was left behind by step 2. Use the angle grinder again, this time with a 6mm grinding disc. As you get close to your lines, try and keep your strokes long to make the edge as smooth as you can. If there are minor high or low spots, smooth those out by hand with a file.

Step by Step Guide on How to Make a Sword


STEP FOUR: Final Shaping

Begin to grind in the bevel. Make sure your centre line is clearly marked first. Start with a steep angle at the edge of the blade, and then smooth it out to the centre line. Once again, try to keep it as smooth as you can. Going all the way down the length of the blade with each stroke takes some time, but it gives the best results. Don't try to get it perfectly sharp; it's good to leave at least a millimetre thickness at the edge of the blade to keep up the blade's strength before heat treating.

BEFORE

Step by Step Guide on How to Make a Sword

AFTER

Step by Step Guide on How to Make a Sword

Use a belt sander to smooth away the rough edges left by the angle grinder.

Step by Step Guide on How to Make a Sword


STEP FIVE: Heat Treating

Since this is a very basic 'how to make a sword' guide for beginners, we'll assume that you don't have your own forge. Most manufacturers that supply steel will heat treat your blade for a nominal fee, so take your newly shaped blade back to a local steel supplier and request that it be heat treated.

Heat treating is very important to ensure that your sword is flexible enough for cutting and resists taking a set on a bad cut.

Step by Step Guide on How to Make a Sword

This is how it will look after heat treatment. That dull finish can be removed by sanding.


STEP SIX: Crossguard and pommel

6. a) Crossguards and pommels are available online if you wish to purchase them (Click here for some recommendations), though they will have to be adjusted to fit the tang on your blade. If you want learn how to make a sword cross guard and pommel from scratch, making the crossguard is very similar to steps 1 through 3; design and mark out the shape that you want on your steel, cut out the shape and refine it. For the pommel, if you can obtain a steel rod that makes your job a bit easier.

Step by Step Guide on How to Make a Sword

Step by Step Guide on How to Make a Sword

6. b) Drill (a drill press is invaluable for this task) holes in the crossguard that will be filed out to make room for the tang. Make sure it is a snug fit, don't make the holes too wide. Drill through the pommel as well.

Step by Step Guide on How to Make a Sword

6. c) Clean out the rough holes made by the drill using a dremel and a needle file. The holes should be snug enough to the tang that you need a mallet to get them on. The crossguard can be affixed to the tang at this point, though leave the pommel until after the wood for the grip is finished.


STEP SEVEN: Make the handle

Choose the wood for the grip – European Beech is often historically used, though any hardwood should work just fine. Cut two lengths needed to fit between the crossguard and the pommel (the two halves will be hollowed out and then epoxied together around the tang). Round the wood with a belt sander.

Step by Step Guide on How to Make a Sword

Measure the width of your tang at the base and at the tip and mark the inside of the wood, then make a shallow cut along the lines with a hacksaw.

Step by Step Guide on How to Make a Sword

Chisel out in between the cuts.

Step by Step Guide on How to Make a Sword

Use a dremel to smooth out the inside so that the wood will rest comfortably next to the tang.

Step by Step Guide on How to Make a Sword

Place the two halves of the grip along the tang, liberally applying epoxy to both of them and clamp them in place for them to dry.

Step by Step Guide on How to Make a Sword

After it's dry, the grip can be refined a bit with a belt sander to taper it or give it a slightly different shape.

OPTIONAL REFINEMENT: You may decide to leather or wire wrap your wooden hilt so that it looks like this:

Wrapping a Sword Handle


Click here for a step by step guide


STEP EIGHT: Put it all together

Put the pommel in place on the tang above the wood, using (you guessed it) more liberally applied epoxy. Trim down the end of the tang so it's about 3 mm past the pommel. To peen the end of the tang, cut down the middle of it using the dremel with a small cutoff wheel. Use a chisel to spread the two halves apart so you can hammer it flat. Before hammering – rest the tip on a few pieces of wood, and make sure it is over soft ground in case the blade goes through. Now hammer away. It will probably take a degree of violence. Do try to be careful though, you certainly don't want to damage the sword you've worked so hard on to get this far. Take the angle grinder and remove any excess left and then sand it to smooth it out.

Step by Step Guide on How to Make a Sword

Step by Step Guide on How to Make a Sword


STEP NINE: Final sharpening and polish

To get a nice edge and shine on your new baby, polish using sandpaper with a finer and finer grit. If you alternate directions (for example going along the blade with 120 grit, then across with 240, diagonal with 320, etc.) then it's easier to see when you have successfully worn down the lines left by the rougher paper.


STEP TEN: ENJOY!

Step by Step Guide on How to Make a Sword


I hope this ten step guide on how to make a sword has been helpful and encourages you to experiment with various styles to create your own home made armory! While not everyone wants to make their own sword, for those of you who want to know how to make a sword and to try their hand, this guide should be enough to get you going!


More links and information will be added to this basic tutorial over the coming weeks and months, so stay tuned for more! In the meantime, To return to the Sword Manufacturers Guide Homepage from How to Make a Sword - a Beginners 10 Step Guide, click here




FREE ONLINE MAGAZINE
Online Magazine

Email

Name

Then

Don't worry -- your e-mail address is totally secure. I promise to use it only to send you Sword Buyers Digest.

Sign up for our monthly newsletter 'the Sword Buyers Digest'!

Click here for more info



[ ?] Subscribe To This Site

XML RSS
Add to Google
Add to My Yahoo!
Add to My MSN
Subscribe with Bloglines



Home  |   Newsfeed  |   About SMG  |   Privacy Policy  |

Copyright© 2007-2010 - www.sword-manufacturers-guide.com - All Rights Reserved
Return to Top